MG34 Receiver Basic Dimensions

The resting place of MG34 Knowledge.

MG34 Receiver Basic Dimensions

Postby 762x51 » Sat May 02, 2009 11:37 pm

Here is a drawing showing the major dimensions needed for re-welds.
All NFA rules apply.

You can see the full size drawing here: http://www.autochart.com/MG34/MG34RecBasicDim.jpg

Image
"It is well that war is so terrible -- lest we should grow too fond of it." Gen. R.E. Lee CSA
Skype ID: ACE1100
User avatar
762x51
Oberst
Oberst
 
Posts: 580
Joined: Wed Mar 09, 2005 7:31 pm
Location: North Carolina

Re: MG34 Receiver Basic Dimensions

Postby rocco1911 » Sun May 03, 2009 8:20 pm

Thank you for posting this ... :wnana:
I'm an expert @ what won't work & what not to do.
rocco1911
General
General
 
Posts: 1226
Joined: Sun Dec 10, 2006 8:42 pm
Location: Arizona

Re: MG34 Receiver Basic Dimensions

Postby Bil » Sun May 03, 2009 9:08 pm

Yes,thanks,Orin.I tried to do this once and made a mess of it. :( It will be handy when I try to figure out if I have enough material for a receiver. ---bil
"I dream of a world where I can buy alcohol,tobacco and firearms from the same drive-up window,and use them all on the way home from work!" Dogbert
Bil
Field Marshal
Field Marshal
 
Posts: 5155
Joined: Sun Nov 26, 2006 9:21 pm
Location: Brookline,VT

Re: MG34 Receiver Basic Dimensions

Postby 762x51 » Mon May 04, 2009 6:21 am

Glad to help guys. Let me know if you need any other dimension.

Orin

Image
"It is well that war is so terrible -- lest we should grow too fond of it." Gen. R.E. Lee CSA
Skype ID: ACE1100
User avatar
762x51
Oberst
Oberst
 
Posts: 580
Joined: Wed Mar 09, 2005 7:31 pm
Location: North Carolina

Re: MG34 Receiver Basic Dimensions

Postby 42rocker » Mon May 04, 2009 8:59 am

As said before MANY THANKS for posting this...

Sorry that I missed out on your mg42 receiver cut sale....

Thanks Later 42rocker
42rocker
Field Marshal
Field Marshal
 
Posts: 2636
Joined: Fri Jan 11, 2008 5:03 pm
Location: Hudson, Fl on US HWY 19 North of Clearwater

Re: MG34 Receiver Basic Dimensions

Postby crash520 » Tue Dec 27, 2011 3:22 pm

Thanks 762x51 for posting the good info

Does anyone know if any 34 rec ordnance drawings exist for all the dims of the 34 rec to scratch build one???

C
crash520
Hauptmann
Hauptmann
 
Posts: 134
Joined: Wed Oct 05, 2011 9:08 pm

Re: MG34 Receiver Basic Dimensions

Postby 42rocker » Tue Dec 27, 2011 4:29 pm

There has been several good posts on this website about making one. However that said take a good look at the following website

http://www.tnwfirearms.com/photos.shtml

Note the equipment that they use to make the receivers. There has been talk about edm equipment and other things being used. I wish you a lot of luck.

Lots of folks buy several mg34 cut receivers and re-weld them...

Later 42rocker
42rocker
Field Marshal
Field Marshal
 
Posts: 2636
Joined: Fri Jan 11, 2008 5:03 pm
Location: Hudson, Fl on US HWY 19 North of Clearwater

Re: MG34 Receiver Basic Dimensions

Postby Bil » Fri Dec 30, 2011 2:48 pm

for prints,try Maschinengewehr34.com Glenn Fahrquhar He sold some sets here,









i have one somewhere,but as mentioned above,the expensive machinery used would keep most from going the avenue. ---bil
"I dream of a world where I can buy alcohol,tobacco and firearms from the same drive-up window,and use them all on the way home from work!" Dogbert
Bil
Field Marshal
Field Marshal
 
Posts: 5155
Joined: Sun Nov 26, 2006 9:21 pm
Location: Brookline,VT

Re: MG34 Receiver Basic Dimensions

Postby 42rocker » Fri Dec 30, 2011 6:10 pm

The set of prints that Fahrquhar put out are nice ones. Think long and hard before you think of starting to make a mg34 receiver from scratch. That said it's been done by several countries and at least one company.

Later 42rocker
42rocker
Field Marshal
Field Marshal
 
Posts: 2636
Joined: Fri Jan 11, 2008 5:03 pm
Location: Hudson, Fl on US HWY 19 North of Clearwater


Return to MG34 Stickies



Who is online

Users browsing this forum: No registered users and 1 guest