MG-42 BRP Build
Re: MG-42 BRP Build
Steps 90 - 93
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 94 - 96
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 97 - 102
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 103 - 105
- Attachments
-
- 105 - Place rivet head in the middle of the tool mark. Put the stud gun over the top. Press down on the rivet gun until the outer ground is against the receiver. Push the button 3 times for 2 sec each time. After the rivet cools take a pair of pliers to make sure the head is securely welded. Install the other two rivets using this step.
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 106 and 107
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 108 – 118 are for a bolt hold open lock. It is not original to the MG42. You can omit these steps if you like. I don’t like to smash my fingers.
Steps 108 - 110
Steps 108 - 110
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 111 - 114
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 115 - 118
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 119 - 124
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 125 -129
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 130 - 135
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 136 & 137
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 138 - 142
- Attachments
-
- 139 - Measure the distance between the front of the charging handle push off bar and the ratchet plate. (139G) Mine is 5mm. Subtract 138F – 139G = (139H) Mine is 8mm – 5mm = 3mm. This is the how much needs to be cut off of the ratchet plate. Measure in 139H on the ratchet plate and mark it. Now measure from that mark to the front of the ratchet plate. (139I) Mine is 17mm. Cut a piece of Key Stock to the length of 139I (same key stock that was used in step 111)
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 143 - 146
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 147 - 152
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 153 - 157
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Steps 158 - 161
- Attachments
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
Finial 3 Steps 162 - 164
- Attachments
-
- 163 - Attach all the remaining rivet heads using the stud gun. 3 large rivet heads go on the buffer tabs. 1 large rivet head goes on the recoup stop/ trigger bracket. 1 large rivet head goes on the left front barrel stop. 8 small rivet heads go on the rails. The last 2 small rivet heads go on the front AA sight mount.
Spell check is down and I'm too lazy to get the dictionary
Re: MG-42 BRP Build
I can't thank you enough for going to all of this trouble for us new guys. You're a great man.
Re: MG-42 BRP Build
This will help greatly with my build. Looking closely at your trigger pack I see that it isn't the regular AR15 profile. It appears you used part of the original trigger to cover the AR15 trigger. Would you share with us how you did this?
Thanks
Robert
Thanks
Robert